Raising the Mast on Jack Frost. By using the small boat’s mast as a gin pole, all the guys can just stand around and watch!
No flat spots in the cockpit opening of Frank Able’s new Whizz
The fleet, dressed in their stormy best for the Long Way, Moosehead Lake
Storm conditions on Moosehead, closing day, April 6, 2013
Opening day on Plymouth, Nov. 30, 2012
Bill and Jory on Great Pond, headed for the narrows
Scorpion ice on Great Pond, Belgrade.
The back door to Bailey’s Cove, Lake Megunticook
There’s ice down there somewhere…
Fast sailing!
Squaring it up
Assembling the hollow plank
Where round bottom ends and rear flat bottom begins
Trimming the deck edge
Cables go nearly straight from wheel to bow chock
Steering gear in place
Seat back laminated from two pieces of 1/8″
Mast step area, with tubes for foot steering shafts visible
Setting up a new Whizz
Early season Plymouth at it’s best
Ben Fuller on board Tipsy
Best way to sheet a wing mast
Pastoral scene on Lake Damariscotta
Hollowing the center of a Renegade mast
Carbon/foam wing mast: the engine of the Whizz
John Eastman’s Meade “Clyde”, built by
Bill Buchholz
Sunset across the bow on Plymouth Pond
Whizz cockpit
Monotype XV and new Meade on Chickawaukee
Mysterious ice circle in freshly frozen slush
South Twin Lake, in the shadow of Mt. Katahdin. The Lambs and others are out there somewhere, too. March, 2013
Lake Damariscotta
A nose ahead, a century behind
megunticook sundown
A current project, at pocket skeeter WHIZZ, spring 2011. Ice is coming: gotta be ready!
Tom Childs pulling the plank on the 2011 season.
Woodman, Buchholz and Paul Delnero on Sebago, last sailing day of 2011 and one of the best.
Jory attempting to dismantle the pressure ridge on Sebago.
Set up in the shop to measure for shrouds and finalize sheet leads, not to mention just staring in wonder at the magic of the building process.
Steering gear exiting hull near access port.
Backing plate let in flush to plank, streamlined button head bolts replace the typical hex heads.
Hull under a layer of six ounce glass and ready for primer; the best time to drill for all the hardware. Here, squaring up the plank to the hull
Fairing the seams and puttying the staple holes.
A closer look.
Trimming the deck edge with an appropriate tool.
Gluing on the bottom
Fitting the bottom
Cleats are added to all the lower edges to provide gluing surface for the bottom. Back aft we;ll use fillets, as the access is good we don’t want to bother with steaming the long cleat.
Bulkheads are filleted and glassed on both sides. Best to lay the glass when the fillets are semi-soft to avoid having to sand them.
Mast step area.
Bulkheads going in.
All the inside seams are taped with three inch tape. The rear bulkhead was installed earlier to help control the shape.
Making sure there’s no twist in the hull.
Sides and deck in place. The battens at the seams are stapled from the inside to help keep the seams fair. Very difficult with eighth inch ply. The seams are now filled with epoxy
Creative clamping at the stern where all the planks converge.
The planks are fastened temporarily to the bulkheads with hot glue.
The planks have been cut out with a router.
The following photos describe the building of an Icywood/DN crossover for Ron Buzzel
The happy skipper.
Scott Woodman’s Outlaw
James Lamb doing what he does on South Twin.
Buchholz and Coward on their annual “sail to the end of the ice excursion”, but this year the ice never ended but the wind did.
Out of wind on Lake South Twin
Morning on South Twin Lake, Millinockett, ME. Two Lambs, Squibb, Buchholz and Coward, late March 2011
Double no comment…
No Comment…
You don’t need to sail a mile a minute to have your breath taken away by the ice.
Saltonstall’s BLACK FLY and Randy Rice’s new build to that design. A memorable day!
Picnic on The Sebago, 2011
Family of ICW class, The Sebago 2011
Long Pond, MA 2011
Long Pond, 2011. Brian Langly’s ICE CAT.
Long Pond, MA. Worth every mile from Maine! 2011
Late days sun
Maiden voyage of Icywood DN crossover.
Praying it will be thick enough for sailing.
The ice checker’s kit, less the throw line.
Taking a break. Squibb,Buchholz, Bunting and Woodman
Storm sails indicates windy day.
Lloyd and Jory discussing the crossing of the pressure ridge.
Reflection of mast and sail in excellent ice.
Welcome, OUTLAW, to CIBC. Plymouth 11-30-10
Blowing through the snow on Damariscotta 2010
Fun in the Snow with SkimBats and ice flyer Iceabella.
Side by side, neck and neck. Long Pond, Harwich
iceboating long pond lakeville jan 31 09, jory and bill having fled snow bound Maine
Even as the spring ice is rotting around the edges, the middle is usually still very sailable. The bad spots are marked, and its off to the races.
Bill Bunting’s RED HERRING passing Indigo by bearing away.
Usual suspects lining up on Megunticook
Ice this rough makes for a bone jarring ride, especially in a DN. But with wind and sunshine and the whole of Sebago ahead, one accepts the comprimise.
Hidden treasures on an ice checking expedition, Unity Pond.